Guide

Terrain

SiteCAD gives you precise control over elevation data — from global context terrain down to sub-meter grading edits. Learn how terrain layers work, how to shape the ground with brush tools, and how to visualize and export your earthwork.

Terrain Layers

Ground data is organized as a stack of terrain layers, managed from the Layers tab in the side panel. Each layer carries up to three sources — elevations, imagery, and a 3D model — and the three resolve independently down the stack. The topmost visible layer is the editing layer, and that is where your brush edits and imports are stored.

Editing layer

Your grading

The topmost visible layer, which the brush edits. It typically starts with no sources of its own, so everything below shows through until you paint. The first brush stroke on a piece of ground copies that ground down from whatever is resolving there and starts editing the copy — so a grading alternative costs nothing until you actually grade something.

Survey layer

Your existing conditions

A layer whose sources are your own survey data — a high-resolution bare-earth elevation model from drone photogrammetry or LiDAR, an orthomosaic for imagery, and optionally a photogrammetry mesh as its 3D model. Within your site it replaces the global default with much higher detail.

Default

Cesium World Terrain

The bottom of every stack, with satellite imagery alongside it. Always available, no setup required. Resolution varies by location but is typically 30 m or coarser — useful for context but not detailed enough for engineering.

How the stack resolves:

Elevations and the 3D model each fall through on their own. Elevations come from the highest layer that has edited ground at that spot, or from the highest layer with an elevation source; the model from the highest layer with a model. Imagery stacks instead: every visible layer's imagery is drawn, higher layers over lower ones, each at its own opacity, so a newer orthomosaic can blend over an older one and the older one still shows wherever the newer does not reach. So your grading can sit on your survey's elevations while your orthomosaic still draws underneath it. Hiding a layer takes it out of the stack without deleting anything it owns.

Where Terrain Comes From

There is no separate step to prepare terrain before editing it. Every site already has ground under it, and the brush works on that ground directly. Bringing in your own survey data is a separate — and optional — piece of setup.

Editing Copies as It Goes

The first time the brush touches a piece of ground, SiteCAD reads the elevations that currently resolve there, stores them on the editing layer, and edits that copy from then on. Ground you never touch stores nothing at all, which is why sites of several square kilometers stay manageable. You never see or place the underlying storage — there is no object to create, no grid to line up with, and no seam where edited ground meets untouched ground.

Every stored point also remembers how far it has moved from the elevation it started at. That difference is what the cut/fill overlay draws, and it is why changing a layer's elevation source later keeps your grading instead of discarding it.

Managing the Stack

Open the Layers tab in the side panel. Each row is one layer; the editing layer's row is marked with a pen, and clicking another row makes that layer the editing layer by hiding the layers above it. The controls on a row are:

  • Show / hide — take a layer out of the stack without deleting what it owns
  • Edit layer — opens the layer's settings under its row, one layer at a time: rename it, set its terrain, imagery, and 3D model sources (an existing geostore asset, or Upload new… to upload a file for that source; two assets sharing a name show the date each was uploaded, and Manage assets… leaves for Account → Assets to rename or delete one), and set its cut/fill options
  • Delete layer — remove the layer and everything it owns

At the top of a layer's settings, Move up and Move down reorder it, Import terrain override… and Import imagery override… bake a local GeoTIFF onto it when it is the editing layer, and Export LandXML… saves the ground it holds.

Add Layer at the bottom stacks a new empty layer on top — the usual way to start new grading without disturbing what is underneath. Duplicate, in the layer's settings, copies a layer — its sources, edits, imagery, and painted materials — into a new layer above it, and the copy keeps that ground even if the original is deleted. To compare design alternatives, branch the scenario instead.

Tip:

The AI assistant and operations scripts can drive the same stack — adding layers, choosing which one to edit, showing and hiding them, and pointing a layer at a different source — using the terrain functions listed under Operations.

Brush Tools

The terrain brush is your primary tool for shaping the ground. Pick it up from the Terrain Brush button in the toolbar, press B, or pick it from the viewport's right-click menu; the toolbar swaps to the brush controls and your cursor becomes a circle on the ground. It works like a painting brush — click and drag to modify elevations in real time. Four modes cover all common grading operations, and a fifth, Revert, returns the editing layer's own ground under the brush to the ground beneath it.

Raise

Pushes terrain upward under the brush. Use for building pads, berms, levees, and fill areas.

Lower

Pushes terrain downward. Use for ponds, drainage channels, excavation, and cut areas.

Smooth

Averages nearby elevations to reduce sharp edges. Use after rough grading to blend transitions.

Flatten

Levels terrain to a target elevation. Use for building pads, parking areas, or any flat surface.

Brush Settings

Radius0.3 – 10 m

Controls the size of the brush circle. Smaller for detail work, larger for broad grading.

Strength0 – 1

How aggressively the brush modifies elevation per stroke. Start low for fine control.

Falloff Smooth, Linear, Gaussian, Constant

How the brush effect tapers from center to edge. Smooth and Gaussian produce natural transitions; Constant applies full effect across the entire radius.

Workflow tip:

Start with a large radius and low strength for rough grading, then switch to a smaller radius for detail. Use Flatten to establish target elevations for pads and platforms, then Smooth to blend edges into the surrounding terrain. Each brush stroke is a single undo step.

Visualization

SiteCAD provides two terrain overlays — contours and cut/fill — plus terrain shading, to help you read the ground surface and the impact of your grading work.

Topographic Contours

Contour lines are traced from the ground surface as it currently resolves — your edits included — using marching squares, and displayed as an imagery overlay. You can configure:

  • Major and minor intervals — e.g., 5 m majors with 1 m minors
  • Index contours — thicker lines at larger intervals for readability
  • Colors and opacity — customize line colors and layer transparency

Contours update live as you brush, giving you immediate feedback on grades and drainage direction.

Cut/Fill Overlay

The cut/fill overlay compares each terrain layer against the original background terrain to classify it as cut or fill:

  • Cut areas (below original) — dark soil tones on the default Dirt ramp, blue on the color ramps
  • Fill areas (above original) — light earth tones on Dirt, red-brown on the color ramps
  • Ramp mode — Dirt texture, Linear color, or Stepped contour, each coloring cut/fill differently; set in the Terrain panel

A per-layer threshold (default 0.05 m, set in the layer's settings) prevents noise in areas with negligible change. The same settings have a per-layer Cut/fill enabled checkbox — a layer with it off is skipped even when the overlay is on. Contours and the cut/fill overlay are independent layers, so both can be visible at once.

Terrain Shading

Shading lights the terrain surface so slopes facing away from the light darken and relief stands out. Choose a mode under Shading in the Terrain panel:

  • Sun (default) — lit by the sun at the simulation time, so it changes through the day
  • Fixed (north-west) — lit from the north-west at 45°, the printed-map convention, so it looks the same at any time; no shadows are drawn
  • Off — the terrain is drawn unshaded; models are still lit by the sun

The Shading strength slider (25–200%) sets how strongly slopes are darkened. While the terrain brush is active it lights the ground from a low south-west angle to show small bumps, and your chosen mode returns when you leave it.

Import & Export

Bring elevation and imagery in from survey and GIS tools, and take your design back out.

Bringing Terrain In

GeoTIFF elevation (.tif, .tiff)

A DTM raster from a drone survey, LiDAR processing, or a GIS export. Read in the browser and baked straight onto the editing layer as edited ground — no upload, no round trip.

GeoTIFF orthophoto (.tif, .tiff)

Aerial imagery, baked onto the editing layer the same way and draped over whatever elevations resolve underneath it.

Uploaded terrain and imagery assets

Larger surveys and orthomosaics are uploaded once, stored in your site’s asset catalog, and set as a layer’s source. They stream in rather than being baked, so they stay cheap at site scale.

Photogrammetry mesh

A textured 3D model is a layer’s third source. It renders above the ground surface and can be clipped where you have placed replacement geometry.

GeoTIFF notes:

A GeoTIFF has to carry a coordinate-reference tag and the band layout SiteCAD expects — elevation in the first band, or RGB/RGBA for imagery. WGS84, NAD83 and the WGS84 UTM zones are reprojected automatically; a file in a State Plane or national grid is refused with a message naming the code, so re-export it in a UTM zone or WGS84. The import runs in the background and reports on the status bar, so you can keep working, and it counts as a single undo step. An import that fails stays flagged on the status bar's Terrain chip until you dismiss it on the layer's row in the Layers tab, so you cannot miss it while you work elsewhere.

Taking Terrain Out

A terrain layer exports as a LandXML surface. Export LandXML… in a layer's settings in the Layers tab writes the ground that layer holds itself — every tile an import baked or the brush sculpted — as one triangulated (TIN) surface, in latitude, longitude and meters above the ellipsoid, that Civil 3D and similar tools read and that SiteCAD imports back as an equal layer. A layer that only shows its base terrain source owns no tiles and has nothing of its own to export, so its button is disabled. Progress shows on the status bar and the export can be canceled there. Cut/fill data and GeoTIFF elevation grids do not come out this way, and there is no terrain mesh export.

What the whole stack travels in is a scenario bundle or snapshot, which carries every layer and every edited tile — the right way to hand a design to a colleague, archive it, or move it between machines. For contractor deliverables, pair the graded layer's LandXML surface with a boundary-and-trace export (GeoJSON, DXF, LandXML) and the design intent.

Continue Learning

Core ConceptsSites, scenarios, entities, and coordinates
Terrain FeaturesFeature overview and capabilities
Getting StartedCreate your first site in 10 minutes
Parametric SolidsCode-driven 3D modeling